]> 2026-05-26T08:19:16+02:00 R0000712F Rotary Trunking 0 en Draft Installation of rotary energy chain and back plates Medium 2 hour(s) '''<u>Tools Required</u>''' Standard set Hex keys Standard socket set Countersink bit and drill Copper/hide hammer Standard hss drill set Hack saw File '''<u>Parts Required</u>''' D0006210 pre assembled energy chain D0003929 Access panel D0003930 Circular guide D0003985 Upper circular guard D0007817 Circular guard D0001171 plug bracket <br/> false en R0000712E_Rotary_Trunking_Screenshot_2024-09-24_091100.png none All bolts must have Loctite 243 adhesive applied unless otherwise stated. All bolts must be marked with pen once completed to indicate adhesive and correct tension has been applied D0003985 needs preparing before fitting 1 All back plates for the rotary trunking need to be checked for correct countersink depth. Any protrusion from main face will case energy chain failure Check and if proud, use a countersink to increase depth 1 Measure position of bracket onto circular guard (291mm) 2 Use a pointed m5 grubscrew screwed into bracket hole indicated, hold in position on guard, and use hide hammer to transfer position mark 3 Drill to 6mm and fix bracket with m5x 16 cap head and large m5 washer 4 Drill 6mm through indicated hole 5 Fix with M5 x 16 countersink, large m5 washer and nyloc nut 6 This countersink bolt head must be flush to block. If proud, use a countersink bit to increase depth Check countersink holes in D0003930 are to the correct depth . Rework with countersink if fasteners sit proud. Check countersink holes in D0007817 are to the correct depth . Rework with countersink if fasteners sit proud. It is vital to achieve correct orientation of above parts Use M8 holes indicated as reference point for fitting Mount D0007817 to main rotary base and fix with m5 x 10 countersink bolts Mount D0003930 to main rotary base and fix with m5 x 10 countersink bolts Mount D0003985 to main rotary base and fix with m5 x 10 countersink bolts Drill and tap m3 to plugged end '''ONLY''' of energy chain assembly Use m3 x 6 pan head bolt to secure <div class="icon-instructions caution-icon"> <div class="icon-instructions-icon"><i class="fa fa-exclamation-triangle"></i></div> <div class="icon-instructions-text">...Caution damage to cables is possible Use a shield over cables to protect</div> </div> Please ensure the following step is noted and replicated This is to ensure the cable and 6mm pipe are located in the correct area on assembly 1 Fit pre assembled R0015304B energy chain assembly plug connection into bracket D00001171 as shown. Note plug has 2 different widths, larger width must be captivated in bracket to ensure secure fitting 2 Mark the indicated area 3 Remove plug connection from bracket and remove marked area using hacksaw and dress with file 4 Refit to bracket, captivating ethercat cable and 6mm blue pipe from energy chain assembly as shown 5 Secure with M4 x 12 socket cap 1 Fix energy chain bracket as shown using 2 off m5 x 10 button heads and heavy washers 2 Add cable retention point. Fit small A0000248 tie base and secure with M4 x 6 button head Fit assembled plug and bracket into position. Secure with 2 off M5 x 10 button sockets 1 Set ethercat cable and 6mm blue pipe to the length shown of 580mm 2 Fit tie wrap to cable restraint point once cable and pipe length are set 1 Slide access panel into position 2 Fix energy chain to panel with m5 x 16 button heads, washers and nyloc nuts Adhesive Prepare 1st guide Section Fit Energy chain mounting bracket Prepare second section Prepare 3rd section Orientation Fit D0007817 Fit D0003930 Fit D0003985 Fit locking screw to energy chain Clarification added to next step on position of cut out on connection plug Mount and mark Connection plug Mount energy chain Mount plug bracket Finalise energy chain cables Fit Access panel 2024-09-24T14:53:45Z 2460578.1206597 R0000712F Rotary Trunking 0 false false 0 0 0 1 plainlist 3 [[:Dokit:DocOptions]] [[DokitEPIEnable::yes]] R0000712F Rotary Trunking# QUERYee7a61aae48f1c3f91d8e4d7736360be