]> 2026-04-27T22:58:11+02:00 ACEpc Changing IP address using netedit 0 en Draft Using the netedit program to change the IP address of an ACEpc running DOS software Easy 5 minute(s) The ACEpcs use two different systems for connecting a network #NETBeui - this was used on earlier machines but reliability depends on the customer network setup. Reconfiguration after initial setup is difficult #IP addressing - A setup system was written using IP addresses to connect. This is a little harder to set up, but is easier to change later. A special program called netedit was written which updates all the correct files in the background false en Manual-ACEpc_ACEpclogo.jpg none This is supplied by customer. IT department <small>''If testing in house it needs to be on the 192.168.16.xxx range.''</small> <small>''e.g 192.168.16.101''</small> If this is for a Flowline - Build Number of Flowline machining center Otherwise this will be the net NETBEUI name of the pc you are connecting to. <small>''For testing at stuga this will be NAS1''</small> If this is for a Flowline - IP Address of Flowline machining center Otherwise this will be the IP address of the pc you are connecting to. <small>''For testing at stuga this will be 192.168.16.6''</small> Ensure the floppy disk is removed and reboot Success will be seen if the machine boots into Drive D: If the saw is connected to a flowline, the saw software should run automatically <nowiki>Press escape - then Y<br /><br />The message:<div class="mw-highlight mw-content-ltr" dir="ltr"><pre>Unable to open params.saw file</pre></div><br /><br /><br />is normal.</nowiki> Build number must be unique. If a flowline saw put an "s" on the end. i.e. F073S <div class="icon-instructions caution-icon"> <div class="icon-instructions-icon"><i class="fa fa-exclamation-triangle"></i></div> <div class="icon-instructions-text">...The text edit boxes are not well written and will fail if the right / left cursor keys or Del key is used. You should always overtype the existing text with the full name or IP address</div> </div><br/> This is the subnet mask for the customer factory <div class="icon-instructions info-icon"> <div class="icon-instructions-icon"><i class="fa fa-info-circle"></i></div> <div class="icon-instructions-text">...For Ip addresses beginning with 192.168.. this is generally 255.255.255.0 For other ranges this can vary, so check with customer IT department</div> </div><br/> Leave these settings as-is <div class="icon-instructions info-icon"> <div class="icon-instructions-icon"><i class="fa fa-info-circle"></i></div> <div class="icon-instructions-text">...These are historical settings for old machines that used a Zebra Label print Server PC. The label servicing is now done on winMulti software so a seperate server is not needed</div> </div><br/> <nowiki>At DOS prompt, ensure you are on drive C: by typing<div class="mw-highlight mw-content-ltr" dir="ltr"><pre>c:</pre></div>And press enter<br /><br /><br /><br />type<div class="mw-highlight mw-content-ltr" dir="ltr"><pre>netedit</pre></div>And press enter<br /><br /><br />If the file does not exist, follow the procedure for installing the netedit software using a 'netsetgo' disk<br /><br />[[ACEpc Installing netedit with NetSetGo disk|https://stuga.dokit.app/wiki/ACEpc_Installing_netedit_with_NetSetGo_disk]]</nowiki> Run NetEdit from command prompt Set the saw name Saw IP address Multi Name Multi IP Save + Exit Remove Disk and reboot Set Subnet mask ZLP Settings ACEpc network netedit 2019-09-19T16:34:08Z 2458746.1903704 ACEpc Changing IP address using netedit 0 false false 0 0 0 1 plainlist 3 [[:Dokit:DocOptions]] [[DokitEPIEnable::yes]] ACEpc Changing IP address using netedit# QUERYee7a61aae48f1c3f91d8e4d7736360be