Voir la source de Stuertz Infeed Table Measurements

{{Tuto Details
|Main_Picture=Stuertz_Infeed_Table_Model.jpg
|Main_Picture_annotation={"version":"2.4.6","objects":[{"type":"image","version":"2.4.6","originX":"left","originY":"top","left":-23,"top":21,"width":1498,"height":931,"fill":"rgb(0,0,0)","stroke":null,"strokeWidth":0,"strokeDashArray":null,"strokeLineCap":"butt","strokeDashOffset":0,"strokeLineJoin":"miter","strokeMiterLimit":4,"scaleX":0.42,"scaleY":0.42,"angle":0,"flipX":false,"flipY":false,"opacity":1,"shadow":null,"visible":true,"clipTo":null,"backgroundColor":"","fillRule":"nonzero","paintFirst":"fill","globalCompositeOperation":"source-over","transformMatrix":null,"skewX":0,"skewY":0,"crossOrigin":"","cropX":0,"cropY":0,"src":"https://stuga.dokit.app/images/6/61/Stuertz_Infeed_Table_Model.jpg","filters":[]}],"height":450.16574585635357,"width":600}
|Description=<translate>Critical measurements and settings for an Autoflow infeed table</translate>
|Categories=Software
}}
<translate><br />

=Method=
{{Warning|...Make sure the GX axis is scaled correctly before starting any measurements}}{{Warning|...Ensure the infeed is set at the correct distance from the machining centre (500mm between feet centreline}}<br />

*Use the gripper arm as the measuring stick. The datum must be set so that zero is the  spindle centreline.
*The measure point is when the gripper nose switch is depressed

{| class="wikitable"
|+
!Measurement
!Description
!A2027 Value
!Photo
|-
|Machining Centre to Infeed spacing
|DDistance between centrelines of feet
|500
|
|-
|Zero Datum
|Centreline of spindles
|0
|
|-
|measureStartPosX
|Measuring start position
Should be so that measure sensor is on machining centre side of the profile load fence
| -880
|
|-
|infeedToZeroX
|Distance from zero to profile load fence
|600
|
|-
|stopCylinderToZeroX
|
|
|
|-
|GX Axis Max position
|Maximum travel on GX Axis
After datum, press estop and manually move to end of travel

Note the value and subtract 10mm
|7255
|
|-
|GX Move After Datum
|Ideally set to max profile length+infeedZeroToX+100{{Warning|...Must not exceed GX Max pos}}

|6500+600+100
=7200
|
|-
|GX Minimum Position
|Absolute minimum position of GX
Goal is for gripper nose switch to at least reach saw blade
{{Warning|...Take care with clashing of the Gripper Froward clamp with the MH infeed clamp}}
Ensure the end rubber buffers are set to prevent a mechanical clash beween the 
| -1050
|
|-
|Infeed Horizontal side clamp positions
|These are set up in the clamp setup as the "GripPos" for OuA_P2BFOnx{{Info|...Note - bar end should be set to -9999, as this effectively disables the other end of the bar from influencing the clamp on/off cycle}}<br />
|1-950
2-1480

3-2600

4-3700

5-4800

6-6300

7-7050
|
|-
|GY Min Position
|Limited by the backfence clamping in the saw area
|10
|
|-
|GY Max Position
|
|54
|
|-
|GZ Min Position
|Gripper must not bottom out on the saw tables
|6
|
|-
|GZ Max position
|{{Info|...GY and GZ min / max positions and gripper tooth height (PullGripperHeight) should also be set in the file c:\ddrive\draw.mul}}
|70
|
|}</translate>
{{PageLang
|Language=en
|SourceLanguage=none
|IsTranslation=0
}}
{{AddComments}}
{{Tuto Status
|Complete=Draft
}}